(navigation image)
Home American Libraries | Canadian Libraries | Universal Library | Community Texts | Project Gutenberg | Children's Library | Biodiversity Heritage Library | Additional Collections
Search: Advanced Search
Anonymous User (login or join us)
Upload
See other formats

Full text of "Dell: Latitude E6410 Service Manual"

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

Working on Your Computer 

Removing and Replacing Parts 

Specifications 

Diagnostics 

System Setup 



Notes, Cautions, and Warnings 

E| NOTE: A NOTE indicates important information that helps you make better use of your computer. 

/\ CAUTI ON: A CAUTI ON indicates potential damage to hardware or loss of data if instructions are not followed. 

A\ WARNI NG: A WARNI NG indicates a potential for property damage, personal injury, or death. 

If you purchased a Dell™ n Series computer, any references in this document to Microsoft® Windows® operating systems are not applicable. 



Information in this document is subject to change without notice. 
© 2010 Dell Inc. All rights reserved. 

Reproduction of this material in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. 

Trademarks used in this text: Dell, the DELL logo, Latitude ON, and Latitude are trademarks of Dell Inc.; Intel, Pentium, Celeron, Intel SpeedStep, Intel TurboBoost, and Core are either 
trademarks or registered trademarks of Intel Corporation; Bluetooth is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell under license; Microsoft, Windows, 
Windows Vista, and the Windows Vista start button are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries; Adobe, the 
Adobe logo, and Flash are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries; ATI FirePro is a trademark of 
Advanced Micro Devices, Inc. 

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any 
proprietary interest in trademarks and trade names other than its own. 

June 2010 Rev. A00 



Back to Contents Page 



System Setup 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

• Entering System Setup 

• Boot Menu 

• Navigation Keystrokes 

• System Setup Menu Options 



Your computer offers the following BIOS and System Setup options: 

i Access System Setup by pressing <F2> 

i Bring up a one-time boot menu by pressing <F12> 

i Access the Intel® AMT settings by pressing <Ctrl> + <P> 

Entering System Setup 

Press <F2> to enter System Setup and make changes to user-definable settings. If you have trouble entering System Setup using this key, press <F2> when 
the keyboard lights first flash. 

Boot Menu 

Press <F12> when the Dell logo appears to initiate a one-time boot menu with a list of the valid boot devices for the computer. Diagnostics and Enter Setup 
options are also included in this menu. The devices listed on the boot menu depend on the bootable devices installed in the computer. This menu is useful 
when you are attempting to boot to a particular device or to bring up the diagnostics for the computer. Using the boot menu does not make any changes to 
the boot order stored in the BIOS. 



Navigation Keystrokes 



Use the following keystrokes to navigate System Setup screens. 



Action 


Keystroke(s) 


Exit BIOS 


<Esc> or click Exit 


Apply a setting 


click Apply 


Reset defaults 


click Load Defaults 


Expand and collapse field 


<Enter> 



System Setup Menu Options 

The following tables describe the menu options for the System Setup program. 



General 


Option 


Description 


System 1 nformation 


This section lists the primary hardware features of your computer. There are no configurable options in this section. 

i System Information 
i Memory Information 
i Processor Information 
i Device Information 


Battery 1 nformation 


Displays the status of the battery and the type of AC adapter connected to the computer. 


Boot Sequence 


Specify the order in which the computer attempts to find an operating system. 

i Diskette drive 

i Internal HDD (IRRT) 

i USB Storage Device 

I CD/DVD/CD-RW Drive 

i Onboard NIC 

i CardbusNIC 

Also allows you to choose the Boot list Option. The options are: Legacy and UEFI 


Date/ Time 


Displays current date and time settings. 



w& NOTE: System Configuration contains options and settings related to integrated system devices. Depending on your computer and installed devices, the 
™" items listed in this section may or may not appear. 



System Configuration 



Option 



Description 



Integrated NIC 



Allows you to configure the integrated network controller. The options are: Disabled, Enabled, and Enabled w/ PXE 
Default Setting: Enabled w/ PXE 



Allows you to configure the parallel port on the docking station. The options are: Disabled, AT, PS2, and ECP 



Parallel Port 



Default Setting: ECP 



Allows you to configure the integrated serial port. The options are: Disabled, COM1, COM2, COM3, and COM4 
Default Setting: COM1 



SATA Operation 



Allows you to configure the internal SATA hard drive controller. The options are: Disabled, ATA, AHCI , and RAID On 
Default Setting: RAI D On 



Miscellaneous Devices 



Allows you to enable or disable the following devices: 



Internal Modem 

Module Bay 

ExpressCard or PC Card 

Media Card, PC Card and 1394 

External USB Port 

Microphone 

eSATA Ports 

Hard Drive Free Fall Protection 

Camera and Microphone 



Default setting: All enabled. 



Latitude ON™ Reader 



Allows you to configure the operating mode of the Latitude ON Reader. The options are: Disabled and Enabled 
Default Setting: Enabled 



Keyboard Illumination 



Allows you to configure the keyboard illumination feature. The options are: Disabled, Auto ALS and I nput, and Auto I nput 
Only 

Default Settings: Disabled 



Video 


Option 


Description 


Ambient Light Sensor 


To enable the Ambient Light Sensor, select the Ambient Light Sensor check box. 
Default Settings: Disabled 


LCD Brightness 


Allows you to set the display brightness depending up on the power source (On Battery and On AC). 



Security 


Option 


Description 


Admin Password 


Allows you to set, change, or delete the administrator (admin) password. When set, the admin password enables several 
security features including: 

i Restricts changes to the settings in Setup 

i Restricts the boot devices listed in the <F12> Boot Menu to those enabled in the "Boot Sequence" field 

i Prohibits changes to the owner and asset tags 

i Substitutes for the system and hard drive password 

NOTE: You must set the admin password before you set the system or hard drive password. 

NOTE: Successful password changes take effect immediately. 

NOTE: Deleting the admin password automatically deletes the system password as well. 

Default Setting: Not Set 


System Password 


Allows you to set, change, or delete the system password. When set, your computer requests you to enter the system 
password every time your computer turns on or restarts. 

NOTE: Successful password changes take effect immediately. 

Default Setting: Not Set 


1 nternal HDD Password 


This field lets you set, change, or delete the password on the system's internal hard disk drive (HDD). Successful changes take 
place immediately and require a system restart. The HDD password travels with the hard drive, so the HDD is protected even 
when installed in another system. 

Default Setting: Not Set 


Password Bypass 


Allows you to bypass the system and internal hard drive password prompts when your computer restarts or resumes from 
standby. 

You can set Password Bypass to Disabled and Reboot Bypass. 

NOTE: You cannot bypass the system or hard drive password when you turn on your computer that has been shut down. 
Default Setting: Disabled 


Password Change 


Allows you to enable the disable permission to the System and Hard Drive passwords when the admin password is set. 
Default Setting: Allow Non- Admin Password Changes checked 


Strong Password 


Allows you to enable of disable option to enforce strong passwords. If enabled, all passwords set on the computer must 
contain at least one uppercase character, one lowercase character and be at least 8 characters long. Enabling this feature 
automatically changes the default minimum password length to 8 characters. 

Default Setting: Disabled 




Allows you to enable or disable the Trusted Platform Module (TPM) on the computer. 

NOTE: Disabling this option does not change any settings you may have made to the TPM, or delete any information or keys 
you may have stored there. 



TPM Security 



When TPM is enabled, the following options are available: 

i Deactivate— Disables the TPM. The TPM restricts access to the stored owner information and does not execute any 

commands that use TPM resources. 
i Activate— Enables and activates the TPM. 
i Clear— Clears the owner information stored in the TPM. 

Default Setting: Disabled 



Computrace 



Allows you to enable or disable the optional Computrace software. The options are Deactivate, Disable, and Activate. 

NOTE: The Activate and Disable options will permanently activate or disable the feature and no further changes will be 
allowed. 

Default Setting: Deactivate 



CPU XD Support 



Allows you to enable or disable the Execute Disable mode of the processor. 
Default setting: Enabled 



Non-Admin Setup Changes 



Allows you to determine whether changes to the setup options are allowed when an Administrator Password is set. If disabled 
the setup options are locked by the admin password. 



Password Configuration 



Allows you to determine the minimum and maximum length of Administrator and System passwords. 



Admin Setup Lockout 



Allows you to prevent users from entering Setup when an Administrator password is set. 



Performance 


Option 


Description 


Multi Core Support 


Enables or disables multi-core support for the processor. Setting options are: All, 1, and 2 
Default Setting: All 


1 ntel® SpeedStep™ 


Enables or disables the Intel SpeedStep feature. 
Default Setting: Enabled 


Intel® TurboBoost™ 


Enables or disables the Intel TurboBoost performance. 
Default Setting: Enabled 



Power Management 


Option 


Description 


AC Behavior 


Allows you to enable or disable the computer from turning on automatically when an AC adapter is connected. 
Default Setting: Wake on AC Disabled 


Auto On Time 


Allows you to set the time at which the computer must turn on automatically. 

You can set the of days, if any, when you would like the system to turn on automatically. The settings are Disabled, Everyday, 
or Weekdays. 

Default setting: Disabled 


USB Wake Support 


Allows you to enable or disable the ability of USB devices to wake the computer from Standby. 

This feature is only functional when the AC power adapter is connected. If the AC power adapter is removed during Standby, 
the BIOS will remove power from all of the USB ports to conserve battery power. 

Default setting: Disabled 


Wake on LAN/ WLAN 


Allows the computer to turn on by a special LAN signal or from Hibernate state when triggered by a special wireless LAN signal. 
Wake-up from the Standby state is unaffected by this setting and must be enabled in the operating system. 

i Disabled — Do not allow the system to power on when it receives a wake-up signal from the LAN or wireless LAN. 

i LAN Only — Allow the system to be powered on by special LAN signals. 

i WLAN Only — Allow the system to be powered on by special WLAN signals. 

i LAN or WLAN — Allow the system to be powered on by special LAN or wireless LAN signals. 

Default setting: Disabled 


ExpressCharge 


Allows you to enable or disable the ExpressCharge feature. 
NOTE: ExpressCharge may not be available for all batteries. 


Charger Behavior 


Allows you to enable or disable the battery charger. If disabled, the battery will not lose power when the system is connected 
to an AC adapter but it will not charge either. 

Default setting: ExpressCharge 



POST Behavior 


Option 


Description 


Adapter Warnings 


Allows you to enable or disable the BIOS warning messages when you use certain power adapters. The BIOS displays these 
messages if you attempt to use a power adapter that has too little capacity for your configuration. 

Default setting: Enabled. 


Keypad (Embedded) 


Allows you to select one of two methods to enable the keypad that is embedded in the internal keyboard. 

i Fn Key Only — The keypad is only enabled when you hold down the <Fn> key. 

i By Numlock — The keypad is enabled when (1) the Num Lock LED is ON and (2) no external keyboard is attached. Note 
that the system might not notice immediately when an external keyboard is detached. 





NOTE: When Setup is running, this field has no effect— Setup works in the Fn Key Only mode. 
Default setting: Fn Key Only. 


Mouse/ Touchpad 


Allows you to select one of two methods to use pointing devices. 

i Serial Mouse — Disable the integrated touch pad when an external Serial mouse is present. 

i PS/ 2 Mouse — Disable the integrated touch pad when an external PS/2 mouse is present. 

i Touchpad-PS/ 2 — Leave the integrated touch pad enabled when an external PS/2 mouse is present. 

Default setting: Touchpad-PS/ 2. 


Numlock LED 


Allows you to enable or disable the Num Lock LED when the computer boots. 
Default setting: Enabled. 


USB Emulation 


Defines how the BIOS handles the USB devices. USB emulation is always enabled during POST. 
Default setting: Enabled 


Fn Key Emulation 


Allows you to use the <Scroll Lock> key on an external PS/2 keyboard the same way you use the <Fn> key on the computer's 
internal keyboard. 

NOTE: USB keyboards cannot emulate the <Fn> key if you are running an ACPI operating system such as Microsoft® 
Windows® XP. USB keyboards will only emulate the <Fn> key in non-ACPI mode (for example., when you are running a DOS). 

Default setting: Enabled. 


Fast Boot 


Allows you to enable or disable the Fast Boot feature. The following options are available: 

i Minimal — Boot quickly unless the BIOS has been updated, memory changed, or the previous POST did not complete, 
i Thorough — Do not skip any steps in the boot process. 

i Auto — Allow the operating system to control this setting (this works only when the operating system supports Simple 
Boot Flag). 

Default setting: Minimal 


Intel® Fast Call for Help 


Used in conjunction with iAMT 4.0. Allows users to initiate contact with a management console while residing outside of the 
corporate infrastructure (i.e. remote location, behind a firewall or NAT, etc.) Use the check box to enable or disable this feature. 

Default setting: Disabled 



Virtualization Support 


Option 


Description 


Virtualization 


Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel 
Virtualization Technology. 

Default setting: Enabled. 


VT for Direct I/O 


Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Intel 
Virtualization Technology for Direct I/O. 

Default setting: Disabled. 


Trusted Execution 


Specifies whether a Measured Virtual Machine Monitor (MVMM) can utilize the additional hardware capabilities provided by Intel 
Trusted Execution Technology. Virtualization Technology and Virtualization Technology for Direct I/O must be enabled to use 
this feature 

Default setting: Disabled. 



Wireless 


Option 


Description 


Wireless Switch 


Allows you to determine the wireless devices that will be controlled by the wireless switch: WWAN, WLAN, and 
Bluetooth®. 


Wireless Devices 


Allows you to enable or disable the following wireless devices: WWAN, WLAN, and Bluetooth. 



Maintenance 


Option 


Description 


Service Tag 


Displays your computer's Service Tag. If for some reason the Service Tag was not already set, you would be able to use this 
field to set it. 

If a Service Tag has not been set for this computer, the computer will automatically bring up this screen when you enter the 
BIOS. You will be prompted to enter the Service Tag. 


Asset Tag 


Allows you to create a system Asset Tag. The field can only be updated if the Asset Tag is not already set. 



System Logs 



Option 



Description 



Bl OS Events 



Allows you to view and clear BIOS POST events. It includes the date and time of the event as well as the LED code. 



DellDiag Events 



Allows you to view the diagnostic results from Dell Diagnostics and PSA. It includes the time and date, the diagnostic and 
version which was run and the resulting code. 



Thermal Events 



Allows you to view and clear thermal events. It includes the date and time as well as the name of the event. 



Power Events 



Allows you to view and clear power events. It includes the date and time of the event as well as the power state and reason. 



Back to Contents Page 



Back to Contents Page 



Diagnostics 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

• Device Status Lights 

• Battery Status Lights 

• Battery Charge and Health 

• Keyboard Status Lights 

• LED Error Codes 



Device Status Lights 



(!) 



a 



Turns on when you turn on the computer and blinks when the computer is in a power management mode. 

Turns on when the computer reads or writes data. 

Turns on steadily or blinks to indicate battery charge status. 

Turns on when wireless networking is enabled. 

Turns on when a card with Bluetooth® wireless technology is enabled. To turn off only the Bluetooth wireless 
technology function, right-click the icon in the system tray and select Disable Bluetooth Radio. 



Battery Status Lights 



If the computer is connected to an electrical outlet, the battery light operates as follows: 

Alternately blinking amber light and blue light — An unauthenticated or unsupported, non-Dell AC adapter is attached to your laptop. 
Alternately blinking amber light with steady blue light — Temporary battery failure with AC adapter present. 
Constantly blinking amber light — Fatal battery failure with AC adapter present. 
Light off — Battery in full charge mode with AC adapter present. 
Blue light on — Battery in charge mode with AC adapter present. 



Battery Charge and Health 

To check the battery charge, press and release the status button on the battery charge gauge to illuminate the charge-level lights. Each light represents 
approximately 20 percent of the total battery charge. 

For example, if four lights are on, the battery has 80 percent of its charge remaining. If no lights appear, the battery has no charge. 

To check battery health using the charge gauge, press and hold the status button on the battery charge gauge for at least 3 seconds. If no lights appear, the 
battery is in good condition and more than 80 percent of its original charge capacity remains. Each light represents incremental degradation. If five lights 
appear, less than 60 percent of the charge capacity remains, and you should consider replacing the battery. 

Keyboard Status Lights 

The green lights located above the keyboard indicate the following: 
yq\ Turns on when the numeric keypad is enabled. 

fin Turns on when the Caps Lock function is enabled. 

\±\ Turns on when the Scroll Lock function is enabled. 



LED Error Codes 

The following table shows the possible LED codes that may display in a no-POST situation. 



Appearance 


Description 


Next Step 


ON-FLASH-FLASH 1 


No SODIMMs are installed 


1. Install supported memory modules. 

2. If memory is already present, reseat the module(s) one at 
time in each slot. 

3. Try known good memory from another computer or replace the 
memory. 

4. Replace the system board. 


[ FLASH-ON-ON 








System board error 



1. Reseat the processor. 

2. Replace the system board. 

3. Replace the processor. 



FLASH-ON-FLASH 




Display panel error 



1. Reseat the display cable. 

2. Replace the display panel. 

3. Replace the video card/system board. 



OFF-FLASH-OFF 




Memory compatibility error 



Install compatible memory modules. 

If two modules are installed remove one and test. Try the 

other module in the same slot and test. Test the other slot 

with both modules. 

Replace the memory. 

Replace the system board. 



ON-FLASH-ON 




Memory is detected but has 
errors 



Reseat the memory. 

If two modules are installed remove one and test. Try the 

other module in the same slot and test. Test the other slot 

with both modules. 

Replace the memory. 

Replace the system board. 



OFF-FLASH-FLASH 




Modem error 



1. Reseat the modem. 

2. Replace the modem. 

3. Replace the system board. 



FLASH-FLASH-FLASH 




System board error 



Replace the system board. 



FLASH-FLASH-OFF 




Option ROM error 



1. Reseat the device. 

2. Replace the device. 

3. Replace the system board. 



OFF-ON-OFF 




Storage device error 



Reseat the hard drive and optical drive. 

Test the computer with just the hard drive and just the optical 

drive. 

Replace the device that is causing the failure. 

Replace the system board. 



FLASH-FLASH-ON 




Video card error 



Replace the system board. 



Back to Contents Page 



Back to Contents Page 



Removing and Replacing Parts 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 



ATG Port Cover (for E6410 ATG computers only) 

SIM Card 

ExpressCard 

Optical Drive 

Access Panel 

coin-cell battery 

WWAN Card 

Latitude ON™ Card/CMG Module 

Heat Sink and Processor Fan 

Modem Connector Plug 

LED Cover 

Display Bezel 

Display Panel 

Fingerprint Reader 

Bluetooth Card 

System Board 

Modem Connector 

SD Card Reader 



• Battery 

• SD Card 

• Smart Card 

• Hard Drive 

• Hinge Covers 

• Memory 

• WLAN Card 

• Processor Fan 

• Processor 

• Modem 

• Keyboard 

• Display Assembly 

• Camera 

• Palm Rest 

• ExpressCard Cage 

• IEEE 1394 Port 

• Power Connector 

• I/O Connector 



Back to Contents Page 



Back to Contents Page 



Specifications 



Dell™ Latitude™ E6410/E6410 ATG Service Manual 



System Information 

Processor 

Memory 

Video 

Audio 

Communications 

ExpressCard 

PC Card 

Secure Digital (5D) Memory Card Reader 

Contactless Smart Cards (Optional) 



Fingerprint Reader (Optional) 

Ports and Connectors 

Drives 

Display 

Keyboard 

Touchpad 

Battery 

AC Adapter 

Physical 

Environmental 



NOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start-> Help and Support and select the 
option to view information about your computer. 



System Information 


Chipset 


Mobile Intel® 5 series chipset (QM57) 


Data bus width 


64 bits 


DRAM bus width 


dual-channel 64 bits 

NOTE: You must install memory in pairs for the dual 
channel mode to work. 


Flash EPROM 


SPI 32 Mbits 


PCI bus 


32 bits, 33 MHz 



Processor 


Types 


Intel Core™ i5 series 
Intel Core i7 series 


L2 cache 


Intel Core i5-520M/540M Dual Core - 3 MB 
Intel Core i7-620M Dual Core - 4 MB 


External bus frequency 


1066 MHz 



Memory 


Type 


DDR3 SDRAM 


Speed 


1066 MHz 


Connectors 


two SODIMM connectors 


Module capacities 


1 GB, 2 GB, 4 GB 


Minimum memory 


1 GB 


Maximum memory 


8 GB 

NOTE: Only 64-bit operating systems can detect 
memory capacities greater than 4 GB. 



Video 


Type 


E6410 — UMA or Discrete video controller 
E6410 ATG - UMA 


Controller 




UMA 


Intel Graphics Media Accelerator HD 


Discrete 


NVIDIA Quadro NVS 3100M 


Output 


15-pin VGA connector 
20-pin DisplayPort connector 

NOTE: DisplayPort, DVI, and VGA is offered through 
the docking station. 



Audio 


Type 


two-channel high-definition audio codec (HDA) 


Controller 


IDT92HD81B Controller 


Speaker 


two 



Internal speaker amplifier 


1 W channel 


Volume controls 


volume up, volume down, and mute buttons 



Communications 


Modem 


internal modem (optional) 


Network adapter 


10/100/1000 Mbps Intel 82577LM Gigabit Ethernet 
Controller 


Wireless 


dedicated WLAN, WWAN, and Bluetooth® 


GPS 


mobile broadband mini-card 



ExpressCard 


NOTE: The ExpressCard slot does 


NOT support PC Cards. 


ExpressCard connector 


ExpressCard slot 


Cards supported 




54 mm ExpressCard 
34 mm ExpressCard 

NOTE: You can order E6410 with either an 
ExpressCard slot or a PC card slot. 

NOTE: E6410 ATG does not support ExpressCards. 



PC Card 


NOTE: The PC card slot does NOT 


support ExpressCards. 




PC card connector 


PC card slot 


Cards supported 




54 mm PC Cards 








NOTE: You can order E6410 with either a PC 


card or 






an ExpressCard slot. 








NOTE: E6410 ATG supports PC Cards only. 





Secure Digital (SD) Memory Card Reader 



Cards supported 



SD / MMC / SDHC / SDHS / MiniSD / MicroSD / SDIO 



Contactless Smart Cards (Optional) 



Supported Smart Cards and Technologies 



IS014443A - 106 kbps, 212 kbps, 424 kbps, and 

848 kbps 

IS014443B - 106 kbps, 212 kbps, 424 kbps, and 

848 kbps 

IS015693 

HID iCIass 

FIPS201 

NXP Desfire 



Fingerprint Reader (Optional) 



Type 



swipe fingerprint sensor 



Ports and Connectors 


Audio 


microphone connector, stereo headphone/ speaker 
connector 


Video 


one 15-pin VGA connector 

one dual-mode DisplayPort connector 


Network adapter 


one RJ-45 connector 


Modem 


one RJ-11 connector 


IEEE 1394 


one 4-pin connector 


USB 


three USB 2.0-compliant connectors 
one eSATA/USB 2.0-compliant connector 


Memory card reader 


one 6-in-l memory card reader 


Smart card reader 


integrated smart card reader 


Mini-Card 


two half-height mini-card slots 





one full-height mini-card slot 


Docking connector 


one E-Family 144-pin docking connector 



Drives 


Hard drive 


SATA 2 HDD 

SATA 2 Mobile HDD 


Optical drives 


DVD 

DVD+/-RW 

Blu-ray™ 



Display 


Latitude™ E6410 


Latitude™ E6410 ATG 


Type and size 


358.14 mm (14.1 inches) 
diagonal TFT with white 
LED backlight 


358.14 mm (14.1 inches) 
diagonal TFT with white 
LED backlight 


Active area (X/Y) 


303.55 mm x 189.65 mm 
(11.95 inches x 7.46 
inches) 


303.55 mm x 189.65 mm 
(11.95 inches x 7.46 
inches) 


Dimensions 


Height 


207 mm (8.14 inches) 


207 mm (8.14 inches) 


Width 


320 mm (12.59 inches) 


320 mm (12.59 inches) 


Operating angle 


degree (closed) to 160 
degrees 


degree (closed) to 160 
degrees 


Display Option 1 


WXGA + Anti-Glare 


WXGA 


Maximum resolution 


1280(H) x 800 (V) at 
262K colors 


1280(H) x800 (V) at 
262K colors 


Maximum brightness 


220 nits 


730 nits 


Refresh rate 


60 Hz 


60 Hz 


Viewing angle 




Horizontal 


40 degrees/40 degrees 


55 degree/55 degrees 


Vertical 


15 degrees/30 degrees 


45 degrees/45 degrees 


Pixel pitch 


0.2373 mm x 0.2373 mm 


0.2370 mm x 0.2370 mm 


Display Option 2 


WXGA + Anti-Glare 


WXGA (Touch feature) 


Maximum resolution 


1440 (H) x 900 (V) at 
262K colors 


1280(H) x 800 (V) at 
262K colors 


Typical brightness 


300 nits 


630 nits 


Refresh rate 


60 Hz 


60 Hz 


Viewing angle 






Horizontal 


40 degrees/40 degrees 


55 degrees/55 degrees 


Vertical 


15 degrees/30 degrees 


45 degrees/45 degrees 


Pixel pitch 


0.2109 mm x 0.2109 mm 


0.2370 mm x 0.2370mm 



Keyboard 


Number of keys 


United States: 83 keys 
Europe: 84 keys 
Japan: 87 keys 


Layout 


QWERTY/AZERTY/Kanji 


Backlit keyboard 


optional 



Touchpad 


Active area 




X-axis 


68 mm (2.67 inches) 


Y-axis 


38 mm (1.49 inches) 



Battery 


Type 


4-cell "smart" lithium ion (37 WHr) 

6-cell "smart" lithium ion (60 WHr) 

3-year life-time 9-cell "smart" lithium ion (81 WHr) 

9-cell "smart" lithium ion (90 WHr) 

12-cell "smart" lithium ion slice (88 WHr) 


Charge time with computer off 
(with 90 W adapter) 


4-, 6-, 9-cell — approximately 1 hour to 80% capacity 

and 2 hours to 100% capacity. 

12-cell — approximately 3 hours 20 minutes to 100% 

capacity. 


Operating time 


battery operating time varies depending on operating 
conditions and can significantly reduce under certain 
power-intensive conditions. 


Life span 


approximately 300 charge/discharge cycles 


Dimensions 





Depth 






4-cell/6-cell 


206.11 mm (8.11 inches) 


9-cell 


207.77 mm (8.18 inches) 


12-cell 


14.48 mm (0.57 inch) 


Height 




4-cell/6-cell 


19.81 mm (0.78 inch) 


9-cell 


22.10 mm (0.87 inch) 


12-cell 


217.17 mm (8.55 inches) 


Width 




4-cell/6-cell 


47.00 mm (1.85 inches) 


9-cell 


68.83 mm (2.71 inches) 


12-cell 


322.07 mm (12.68 inches) 


Weight 




4-cell 


235.87 g (0.52 lb) 


6-cell 


326.59 g (0.72 lb) 


9-cell 


480.81 g (1.06 lb) 


12-cell 


848.22 g (1.87 lb) 


Voltage 


11.10 VDC 


Temperature range 




Operating 


°C to 35 °C (32 °Fto 95 °F) 


Storage 


-40 °C to 60 °C (-40 °F to 140 


°F) 


Coin-cell battery 


3 VCR2032 lithium coin cell 



AC Adapter 


1 nput voltage 


100 V-240 V~ 


Input current (maximum) 


1.5 A 


1 nput frequency 


50 Hz-60 Hz 


Output power 


65 W or 90 W 


Output current 




65 W (E6410 with UMA video only) 


3.34 A (continuous) 


90 W 


4.62 A (continuous) 


Dimensions 


Depth 




65 W 


127.00 mm (4.99 inches) 


90 W 


147.00 mm (5.78 inches) 


Height 




65 W 


16.00 mm (0.63 inch) 


90 W 


16.00 mm (0.63 inch) 


Width 




65 W 


66.04 mm (2.60 inches) 


90 W 


70.00 mm (2.75 inches) 


Temperature range 




Operating 


°C to 35 °C (32 °F to 95°F) 


Storage 


-40 °C to 65 °C (-40 °F to 149 °F) 



Physical 


Latitude E6410 




Depth 


238.30 mm (9.38 inches) 


Height 


front height: 25.40 mm (1.00 inch) 
back height: 31.20 mm (1.22 inches) 


Width 


335.00 mm (13.10 inches) 


Weight 


1.95 kg (4.30 lb) 


Latitude E6410 ATG 




Depth 


245.80 mm (9.67 inches) 


Height 


front height: 31.20 mm (1.22 inches) 
back height (with port cover): 
39.50 mm (1.55 inches) 


Width 


341.00 mm (13.42 inches) 


Weight (minimum) 


2.68 kg (5.90 lb) 



Environmental 



Temperature range 




Operating 


°C to 35 °C (32 °Fto 95 °F) 


Non-operating 


-40 °C to 65 °C (-40 °F to 149 °F) 


Relative humidity (maximum) 




Operating 


10 % to 90 % (noncondensing) 


Non-operating 


5% to 95 % (noncondensing) 


Maximum vibration 




Operating 


0.66 Grms (2 Hz-600 Hz) 


Non-operating 


1.30 Grms (2 Hz-600 Hz) 


NOTE: Vibration is measured using a random-vibration spectrum that simulates user environment. 


Maximum shock 




Operating 


110 G (2 ms) 


Non-operating 


160 G (2 ms) 


NOTE: Shock is measured with hard drive in head-parked position and a 2-ms half-sine pulse. 


Altitude 




Operating 


-15.20 m to 3048 m (-50 ft to 10,000 ft) 


Non-operating 


-15.20 m to 10,668 m (-50 ft to 35,000 ft) 



Back to Contents Page 



Back to Contents Page 

Access Panel 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Access Panel 




£4 NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Loosen the captive screw that secures the access panel to the base of the computer. 



5. Slide the access panel toward the front of the computer. 

6. Lift and remove the access panel off of the computer. 

Replacing the Access Panel 

To replace the access panel, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

ATG Port Cover 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the ATG Port Cover 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Pry and remove the ATG port cover away from the base of the computer. 



Replacing the ATG Port Cover 

To replace the ATG port cover, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Battery 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Battery 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Slide the battery latches toward the center of the computer. 



3. Slide the battery out of the computer and remove it. 

Replacing the Battery 

To replace the battery, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Bluetooth Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Bluetooth Card 




Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the SIM card . 

5. Remove the SD card . 

6. Remove the ExpressCard . 

7. Remove the Smart card . 

8. Remove the hinge covers . 

9. Remove the access panel . 

10. Remove the optical drive . 

11. Remove the hard drive . 

12. Remove the LED cover . 

13. Remove the keyboard . 

14. Remove the coin-cell battery . 

15. Remove the memory . 

16. Remove the WWAN card . 

17. Remove the WLAN card . 

18. Remove the Latitude ON™ Flash/CMG module . 

19. Remove the Fingerprint Reader . 

20. Remove the Heat Sink and Processor Fan . 

21. Remove the screw that secures the Bluetooth card to the computer. 



22. Disconnect the Bluetooth cable from the computer. 

23. Remove the Bluetooth card from the computer. 

Replacing the Bluetooth Card 

To replace the Bluetooth card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Camera 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 



Removing the Camera 




£4 NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the battery . 

3. Remove the display bezel . 

4. Loosen the captive screw that secures the camera to the computer. 



5. Remove the camera from the slot on the computer. 



6. Disconnect the data cable to remove the camera from the computer. 



Replacing the Camera 

To replace the camera, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

ExpressCard Cage 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the ExpressCard Cage 




Ea NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the Memory Card . 

5. Remove the ExpressCard . 

6. Remove the access panel . 

7. Remove the hinge covers . 

8. Remove the LED cover . 

9. Remove the keyboard 

10. Remove the hard drive . 

11. Remove the fingerprint reader . 

12. Remove the Heat Sink and Processor fan . 

13. Remove the display assembly . 

14. Remove the palm rest . 

15. Remove the screws that secures the ExpressCard cage to the computer. 



16. Lift the ExpressCard cage and slide the ExpressCard cage out of the computer. 

Replacing the ExpressCard Cage 

To replace the ExpressCard cage, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Coin-cell Battery 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Coin-cell Battery 



^f 



^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Disconnect the coin-cell battery cable from the system board. 



6. Lift and remove the coin-cell battery out of its socket. 

Replacing the Coin-cell Battery 

To replace the coin-cell battery, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Display Assembly 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Display Assembly 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the hinge covers . 

5. Remove the access panel . 

6. Disconnect and unthread the antennae cable from the WLAN and/or WWAN card. 



7. Disconnect and unthread the touch screen cable from the system board. (Only applies to E6410 ATG computer). 



8. Loosen the captive screws that secure the display cable to the system board. 



9. Disconnect and unthread the display data cable from the system board. 



10. Remove the screws that secure the display assembly to the computer. 

11. Lift and remove the display assembly from the computer. 

Replacing the Display Assembly 

To replace the display assembly, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Display Bezel 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Display Bezel 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the battery . 

3. Starting from the bottom, gently pry the display bezel inside out from the display assembly using a plastic scribe. 



4. When all the snaps loosen, remove the display bezel from the display assembly. 

Replacing the Display Bezel 

To replace the display bezel, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Display Panel 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Display Panel 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the Display Bezel . 

5. Remove the screws that secure the display panel to the display assembly. 



6. Remove the display panel from the top cover and lay it face down on the palm rest. 



7. Disconnect the touch screen cable (1), and EDP cable (2), from the LCD panel. 

8. Disconnect the touch screen cable if present. 



9. Remove the display panel. 

10. Remove the screws that secure the left display bracket to the display panel. 

11. Remove the screws that secure the right display bracket to the display panel. 

Replacing the Display Panel 

To replace the display panel, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



ExpressCard 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the ExpressCard 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Press and release the card eject button. 



4. Press the card eject button to release the card. 

5. Remove the card out of the computer. 

Replacing the ExpressCard 

To replace the ExpressCard, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Processor Fan 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Processor Fan 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Disconnect the processor fan cable from the system board. 



6. Remove the screws that secure the processor fan onto the heat sink. 



7. Remove the processor fan from the computer. 

Replacing the Processor Fan 

To replace the processor fan, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Fingerprint Reader 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Fingerprint Reader 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the optical drive . 

5. Remove the access panel . 

6. Remove the LED cover . 

7. Remove the keyboard . 

8. Loosen the single captive screw (labeled 'F') on the bottom of the computer, securing the fingerprint reader. 



9. Disconnect the fingerprint reader data cable from the system board. 
10. Peel off the Mylar to release the cable and fingerprint reader from the computer to remove the fingerprint reader. 

Replacing the Fingerprint Reader 

To replace the fingerprint reader, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Hard Drive 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Hard Drive 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the screws that secure the hard drive to the computer. 



5. Slide and remove the hard drive out of the computer. 

6. Remove the screw that secures the hard drive caddy to the hard drive. 

7. Pull and remove the hard drive caddy away from the hard drive. 

Replacing the Hard Drive 

To replace the hard drive, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Heat Sink and Processor Fan 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Heat Sink and Processor Fan 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery 

4. Remove the access panel 

5. Remove the coin-cell battery 

6. Disconnect the fan cable from the system board. 



7. Loosen the captive screws on the heat sink. 

8. Lift the edge of the heat sink that is closest to the center of the computer, and then slide the heat sink out of the computer. 

Replacing the Heat Sink and Processor Fan 

To replace the heat sink and processor fan, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Hinge Covers 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Hinge Covers 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the screws that secure the hinge covers to the computer. 



5. Slide the hinge covers toward the back of the computer and remove the hinge cover. 

Replacing the Hinge Covers 

To replace the hinge covers, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

IEEE 1394 Port 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the I EEE 1394 Port 



Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the SIM card . 

5. Remove the SD card . 

6. Remove the ExpressCard . 

7. Remove the Smart card . 

8. Remove the hinge covers . 

9. Remove the access panel . 

10. Remove the optical drive . 

11. Remove the hard drive . 

12. Remove the LED cover . 

13. Remove the keyboard . 

14. Remove the coin-cell battery . 

15. Remove the memory . 

16. Remove the WWAN card . 

17. Remove the WLAN card . 

18. Remove the Latitude On™ Flash/CMG module . 

19. Remove the Fingerprint Reader . 

20. Remove the Heat Sink and Processor Fan . 

21. Remove the Display Assembly . 

22. Peel back the Ferrite sheet covering the firewire cable. 



23. Disconnect and unthread the firewire data cable from the system board. 



24. Remove the screws that secure the IEEE 1394 board to the computer. 



25. Remove the IEEE 1394 board from the computer. 

Replacing the I EEE 1394 Port 

To replace the IEEE 1394 port, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

1/ O port card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the 1/ O port card 




Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the optical drive . 

5. Remove the hard drive . 

6. Remove the hinge covers . 

7. Remove the access panel . 

8. Remove the coin-cell battery . 

9. Remove the Heat Sink and Processor fan . 

10. Remove the LED cover . 

11. Remove the keyboard . 

12. Remove the display assembly . 

13. Remove the palm rest . 

14. Remove the modem . 

15. Remove the modem connector . 

16. Remove the ExpressCard cage . 

17. Remove the palm rest . 

18. Remove the system board . 

19. Remove the screw that secures the I/O port card to the computer. 



20. Lift the left edge of the I/O port card and remove the I/O port card from the computer. 

Replacing the 1/ O port card 

To replace the I/O port card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Keyboard 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Keyboard 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the LED cover . 

5. Remove the screws that secure the keyboard to the computer. 



6. Use a plastic tab to lift the back edge of the keyboard to release the keyboard. 

7. Slide the keyboard toward the back of the computer and remove the keyboard from the computer. 

Replacing the Keyboard 

To replace the keyboard, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Latitude ON™ Flash/CMG Module 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 



Removing the Latitude ON Flash/ CMG Module 




£4 NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 
1. Remove the battery . 

4. Remove the left hinge cover. (See Removing Hinge Covers ). 

5. Remove the screw that secures the Latitude ON Flash/CMG module. 



6. Remove the Latitude ON Flash/CMG module. 



Replacing the Latitude ON Flash/ CMG Module 

To replace the Latitude ON Flash/CMG Module, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

LED Cover 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the LED Cover 



^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the battery . 

3. Gently pry up one end of the LED cover and remove it. 



Replacing the LED Cover 

To replace the LED cover, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Memory 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Memory Module 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Spread apart the securing clips on each end of the memory module connector until the memory module pops up. 



6. Slide and remove the memory module out of the socket. 

Replacing the Memory Module 

To replace the memory module, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Modem 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Modem 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the LED Cover . 

5. Remove the keyboard . 

6. Remove the screw that secures the modem to the computer. 



7. Using the Mylar tab lift the modem up slightly, and then slide the modem out of its slot. 

8. Disconnect the modem cable from the modem to remove the modem from the computer. 

Replacing the Modem 

To replace the modem, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Modem Connector 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Modem Connector 



*?w 



NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 



1. 


Follow the procedures in Before Working Inside Your Computer. 


2. 


Remove the ATG Port Cover (applicable on E6410 ATG computer only) 


3. 


Remove the battery. 


4. 


Remove the Memorv . 


5. 


Remove the ExpressCard. 


6. 


Remove the optical drive. 


7. 


Remove the hard drive. 


8. 


Remove the hinge covers. 


9. 


Remove the access panel. 


10. 


Remove the Latitude ON™ Flash/CMG Module. 


11. 


Remove the WWAN card. 


12. 


Remove the WLAN card. 


13. 


Remove the coin-cell batterv. 


14. 


Remove the LED cover. 


15. 


Remove the keyboard. 


16. 


Remove the fingerprint reader. 


17. 


Remove the displav assemblv. 


18. 


Remove the ExpressCard cage. 


19. 


Remove the palm rest. 


20. 


Remove the svstem board. 


21. 


Unthread the modem connector cable from the computer. 



22. Lift the modem connector out of its slot and remove. 

Replacing the Modem Connector 

To replace the modem connector, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Modem Plug 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Modem Plug 



^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Insert a pin it into the modem plug eject hole on the modem port plug to release and remove the snap securing it. 



Replacing the Modem Plug 

To replace the modem plug, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Optical Drive 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Optical Drive 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the screw that secures the optical drive to the computer. 



4. Press and release the optical drive latch. 

5. Pull the optical drive out of the computer 

Replacing the Optical Drive 

To replace the optical drive, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Palm Rest 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 



Removing the Palm Rest 







Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the SIM card . 

5. Remove the SD card . 

6. Remove the ExpressCard . 

7. Remove the Smart card . 

8. Remove the hinge covers . 

9. Remove the access panel . 

10. Remove the optical drive . 

11. Remove the hard drive . 

12. Remove the LED cover . 

13. Remove the keyboard . 

14. Remove the coin-cell battery . 

15. Remove the memory . 

16. Remove the WWAN card . 

17. Remove the WLAN card . 

18. Remove the Latitude ON™ Flash/CMG module . 

19. Remove the coin-cell battery . 

20. Remove the Fingerprint Reader . 

21. Remove the Heat Sink and Processor Fan . 

22. Remove the Display Assembly . 

23. Remove the 8 screws (Number 1 is a captive screw) from the bottom of the computer. 

Wa NOTE: If the computer is installed with a standard palm rest, see the fingerprint reader removal instructions from step 8 to loosen the 9th screw 
which is a captive screw. 



24. Remove the screws that secure the palm rest to the computer. 



25. Disconnect the speaker cable (1), power button cable (2), touch pad cable(3), and RFID cable (4). 

Wa NOTE: RFID cable is available only if your computer is purchased with contactless smart card solution. 



26. Lift the back edge of the palm rest and pull on the right side to release the right snaps. Once the right snaps release, pull the palm rest forward along 
the front to release the front snaps and remove the palm rest. 



Replacing the Palm Rest 



To replace the palm rest, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Power Connector 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Power Connector 




Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery 

4. Remove the Memory . 

5. Remove the ExpressCard . 

6. Remove the optical drive . 

7. Remove the hard drive . 

8. Remove the hinge covers . 

9. Remove the access panel . 

10. Remove the Latitude ON™ Flash/CMG module . 

11. Remove the WWAN card . 

12. Remove the WLAN card . 

13. Remove the coin-cell battery . 

14. Remove the LED cover . 

15. Remove the keyboard . 

16. Remove the Fingerprint Reader . 

17. Remove the Display Assembly . 

18. Remove the ExpressCard cage . 

19. Remove the palm rest . 

20. Remove the system board . 

21. Unthread the power source cable from the computer. 



22. Lift up the power source port to remove from the computer. 

Replacing the Power Connector 

To replace the power connector, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Processor 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Processor 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Remove the Heat Sink and Processor fan . 

6. Rotate processor cam lock counter clock-wise. 



7. Lift the processor and remove it from the computer. 

Replacing the Processor 

To replace the processor, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

SD Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the SD Card 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Press in on the SD card and release the SD card. 



3. Pull and remove the SD card out of the computer. 

Replacing the SD Card 

To replace the SD card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

SD Card Reader 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the SD Card Reader 




Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery 

4. Remove the Memory . 

5. Remove the ExpressCard . 

6. Remove the optical drive 

7. Remove the hard drive 

8. Remove the hinge covers 

9. Remove the access panel 

10. Remove the Latitude ON™ Flash/CMG Module . 

11. Remove the WWAN card . 

12. Remove the WLAN card . 

13. Remove the coin-cell battery . 

14. Remove the LED cover 

15. Remove the keyboard 

16. Remove the fingerprint reader . 

17. Remove the display assembly . 

18. Remove the ExpressCard cage . 

19. Remove the system board . 

20. Disconnect the SD card reader cable from the system board. 



21. Lift the 2 hooks while pulling the smart card reader to the right of the computer. 



22. Remove the smart card reader from the computer. 

Replacing the SD Card Reader 

To replace the SD card reader, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

SI M Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the SI M Card 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Press and release the SIM card. 



5. Slide and remove the SIM card out of the computer. 

Replacing the SI M Card 

To replace the SIM card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

Smart Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the Smart Card 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Pull and remove the smart card out of the computer. 



Replacing the Smart Card 

To replace the smart card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

System Board 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the System Board 




Ka NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG port cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the SIM card . 

5. Remove the SD card . 

6. Remove the ExpressCard . 

7. Remove the Smart card . 

8. Remove the hinge covers . 

9. Remove the access panel . 

10. Remove the optical drive . 

11. Remove the hard drive . 

12. Remove the LED cover . 

13. Remove the keyboard . 

14. Remove the coin-cell battery . 

15. Remove the memory . 

16. Remove the WWAN card . 

17. Remove the WLAN card . 

18. Remove the Latitude ON™ Flash/CMG module . 

19. Remove the Fingerprint Reader . 

20. Remove the Heat Sink and Processor Fan . 

21. Remove the Display Assembly . 

22. Remove the palm rest . 

23. Disconnect the power connector from the system board. 



24. Disconnect the smart card reader and IEEE 1394 cables from system board. 



25. Remove the screws that secure the system board to the computer. 



26. Starting in the back right corner and separate the system board from the I/O board connector. 

27. Lift the back edge of the system board until all the connectors on the left side are separated and slide the system board towards the rear and remove 
from the computer. 



Replacing the System Board 

To replace the system board, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

WLAN Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

Removing the WLAN Card 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Disconnect the antenna cables from the WLAN card. 



6. Remove the screw that secures the WLAN card to the computer. 



7. Remove the WLAN card from the computer. 

Replacing the WLAN Card 

To replace the WLAN card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Removing and Replacing Parts 

WWAN Card 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

/■\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 



Removing the WWAN Card 




^ NOTE: You may need to install Adobe® Flash® Player from Adobe.com in order to view the illustrations below. 

1. Follow the procedures in Before Working Inside Your Computer . 

2. Remove the ATG Port Cover (applicable on E6410 ATG computer only). 

3. Remove the battery . 

4. Remove the access panel . 

5. Disconnect any antenna cables that may be connected to the WWAN card. 



6. Remove the screw that secures the WWAN card in the computer. 



7. Remove the WWAN card from the computer. 



Replacing the WWAN Card 

To replace the WWAN card, perform the above steps in reverse order. 
Back to Removing and Replacing Parts 



Back to Contents Page 

Working on Your Computer 

Dell™ Latitude™ E6410/E6410 ATG Service Manual 

• Before Working Inside Your Computer 

• Recommended Tools 

• Turning Off Your Computer 

• After Working Inside Your Computer 



Before Working I nside Your Computer 



Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, 
each procedure included in this document assumes that the following conditions exist: 

i Ensure that you have performed all the steps specified in this section. 

i You have read the safety information that shipped with your computer. 

i A component can be replaced or— if purchased separately— installed by performing the removal procedure in reverse order. 

/:\ WARNI NG: Before working inside your computer, read the safety information that shipped with your computer. For additional safety best 
practices information, see the Regulatory Compliance Homepage at www.dell.com/ regulatory compliance. 

,A CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as 

authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not 
authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 

/\ CAUTI ON: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal 
surface, such as a connector on the back of the computer. 

/\ CAUTI ON: Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges or by its metal 
mounting bracket. Hold a component such as a processor by its edges, not by its pins. 

,A CAUTI ON: When you disconnect a cable, pull on its connector or on its pull- tab, not on the cable itself. Some cables have connectors with locking 
tabs; if you are disconnecting this type of cable, press in on the locking tabs before you disconnect the cable. As you pull connectors apart, keep 
them evenly aligned to avoid bending any connector pins. Also, before you connect a cable, ensure that both connectors are correctly oriented 
and aligned. 

^jj NOTE: The color of your computer and certain components may appear differently than shown in this document. 

To avoid damaging your computer, perform the following steps before you begin working inside the computer. 

1. Ensure that your work surface is flat and clean to prevent the computer cover from being scratched. 

2. Turn off your computer (see Turning Off Your Computer ). 

3. If the computer is connected to a docking device (docked), undock it. 

/"\ CAUTI ON: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. 

4. Disconnect all network cables from the computer. 

5. Disconnect your computer and all attached devices from their electrical outlets. 

6. Where applicable, disconnect any adapters from the computer. 

6. Close the display and turn the computer upside-down on a flat work surface. 

A CAUTI ON: To avoid damaging the system board, you must remove the main battery before you service the computer. 

7. Remove the main battery . 

8. Turn the computer top-side up. 

9. Open the display. 

10. Press the power button to ground the system board. 

/\ CAUTI ON: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the display. 

/\ CAUTI ON: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back 
of the computer. While you work, periodically touch an unpainted metal surface to dissipate static electricity, which could harm internal 
components. 

11. Remove any installed ExpressCards or Smart Cards from the appropriate slots. 

12. Remove the hard drive . 

Recommended Tools 

The procedures in this document may require the following tools: 

i Small flat-blade screwdriver 

i #0 Phillips screwdriver 

i #1 Phillips screwdriver 

i Small plastic scribe 

Turning Off Your Computer 

/\ CAUTI ON: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer. 



1. Shut down the operating system: 
i I n Windows 7®: 

Click Start w and click Shut Down. 
i I n Windows Vista®: 



Click Start *^ , then click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down. 

1 1- -u 



i In Windows® XP: 

Click Start-> Turn Off Computer-* Turn Off. 

The computer turns off after the operating system shutdown process is complete. 

2. Ensure that the computer and all attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut 
down your operating system, press and hold the power button for about 4 seconds to turn them off. 



After Working I nside Your Computer 

After you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turning on your computer. 

/"\ CAUTI ON: To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for 
other Dell computers. 

1. Connect any external devices, such as a port replicator, battery slice, or media base, and replace any cards, such as an ExpressCard. 

2. Connect any telephone or network cables to your computer. 

/\ CAUTI ON: To connect a network cable, first plug the cable into the network device and then plug it into the computer. 

3. Replace the Battery . 

4. Connect your computer and all attached devices to their electrical outlets. 

5. Turn on your computer. 

Back to Contents Page